Salta al contenuto principale
Passa alla visualizzazione normale.

EMMANUEL FORTUNATO GULINO

Curriculum e ricerca

GULINO EMMANUEL FORTUNATO

EMMANUEL FORTUNATO GULINO

 (ING-IND/22)

Ingegneria

Contatti

emmanuelfortunato.gulino@unipa.it

Curriculum non disponibile

Insegnamenti

Anno accademico Codice della materia Nome della materia CFU Corso di studi
2023/2024 17716 TECNOLOGIA DEI MATERIALI (MODULO) 3 INGEGNERIA DELL'ENERGIA E DELLE FONTI RINNOVABILI

Pubblicazioni

Data Titolo Tipologia Scheda
2023 Biodegradable Membrane with High Porosity and Hollow Structure Obtained via Electrospinning for Oil Spill Clean-up Application Articolo in rivista Vai
2023 Release Profiles of Carvacrol or Chlorhexidine of PLA/Graphene Nanoplatelets Membranes Prepared Using Electrospinning and Solution Blow Spinning: A Comparative Study Articolo in rivista Vai
2023 Recycling of Heterogeneous Mixed Waste Polymers through Reactive Mixing Articolo in rivista Vai
2022 An innovative route to prepare in situ graded crosslinked PVA graphene electrospun mats for drug release Articolo in rivista Vai
2022 Opuntia Ficus Indica based green composites for NPK fertilizer controlled release produced by compression molding and fused deposition modeling Articolo in rivista Vai
2022 Hedysarum coronarium-Based Green Composites Prepared by Compression Molding and Fused Deposition Modeling Articolo in rivista Vai
2022 Green Composites Based on Hedysarum coronarium with Outstanding FDM Printability and Mechanical Performance Articolo in rivista Vai
2021 Hydrolytic degradation of PLA/Posidonia Oceanica green composites: A simple model based on starting morpho-chemical properties Articolo in rivista Vai
2021 Green composites based on pla and agricultural or marine waste prepared by fdm Articolo in rivista Vai
2021 A new methodological approach to correlate protective and microscopic properties by soft x-ray microscopy and solid state nmr spectroscopy: The case of cusa’s stone Articolo in rivista Vai
2021 Effect of alkyl derivatization of gellan gum during the fabrication of electrospun membranes Articolo in rivista Vai
2020 PLA-based functionally graded laminates for tunable controlled release of carvacrol obtained by combining electrospinning with solvent casting Articolo in rivista Vai
2020 Processing-structure-property relationships of electrospun PLA-PEO membranes reinforced with enzymatic cellulose nanofibers Articolo in rivista Vai
2020 Bilayer biodegradable films prepared by co-extrusion film blowing: Mechanical performance, release kinetics of an antimicrobial agent and hydrolytic degradation Articolo in rivista Vai
2020 Lignocellulosic fillers and graphene nanoplatelets as hybrid reinforcement for polylactic acid: Effect on mechanical properties and degradability Articolo in rivista Vai
2020 Rapid One-Step Fabrication of Graphene Oxide-Decorated Polycaprolactone Three-Dimensional Templates for Water Treatment Articolo in rivista Vai
2020 The effects of nanoclay on the mechanical properties, carvacrol release and degradation of a pla/pbat blend Articolo in rivista Vai
2020 Structure–property relationship and controlled drug release from multiphasic electrospun carvacrol-embedded polylactic acid/polyethylene glycol and polylactic acid/polyethylene oxide nanofiber mats Articolo in rivista Vai
2019 Structure-property relationship of PLA-Opuntia Ficus Indica biocomposites Articolo in rivista Vai
2019 Tunable release of Chlorhexidine from Polycaprolactone-based filaments containing graphene nanoplatelets Articolo in rivista Vai
2019 Degradation and recycling of films based on biodegradable polymers: A short review Articolo in rivista Vai